Services

Services of Magneto-photonic Laboratory
NO. Service Type Description
1 Heat treatment in air at temperatures up to 1200 C0 per hour​
2 Heat treatment under vacuum at temperatures up to 700 0C - mbar per hour​
3 Heat treatment under vacuum in inert gas atmosphere at temperatures up to 700 0C per hour​
4 NIR-VIS-UV spectroscopy​ each test​
5 Measurement of  Kerr and Faraday effects​ each test​
6 Measurement of Hall effect each test​
7 Measurement of magnetic resistance​ each test​
8 Measurement of magnetic impedance up to 15 MHz​ Per 10 frequencies​
9 Evaporative deposition​ The required materials are provided  by applicant​
10 Evaporative deposition​ The required materials are provided  by laboratory​
11 Spin Coating​ The required materials are provided  by applicant​
12 Spin Coating​ The required materials are provided  by laboratory​
13 Electrochemical deposition The required materials are provided  by applicant​
14 Electrochemical deposition The required materials are provided  by laboratory​
15 Target preparation from basic solid materials The required materials are provided  by applicant​
16 Target preparation from basic solid materials The required materials are provided  by laboratory​
Services of Magneto-plasmonic Laboratory
No. Service Type Description
1 Hysteresis loop measurement  of magneto-optical responses such as Faraday and Kerr rotations​ per data registration for each sample​
2 Measurement of spectral responses of magneto-optical samples in Faraday and Kerr configurations​ per data registration for each sample​
3 Measurement of magneto-electrical response of samples​ per data registration for each sample​
4 Laser deposition of oxide and non-oxide samples in alloy composition Deposition of each sample​
5 Electron beam deposition Deposition of each sample​
6 Thermal deposition​ Deposition of each sample​
7 Response registration of magnetic and non-magnetic circular dichroism​ Per sample​
8 Optical thickness measurement  Per sample​
9 Nanosecond laser spectroscopy Per sample​

Services of Laboratory of Optical Active Devices ​

No. Service Type Description
1 Insertion Loss​ Per sample
2 Return loss Per sample
3 Wavelength Dependent Insertion Loss Per sample
4 Wavelength Dependent Return Loss​ Per sample
5 Polarization Dependent Loss​ Per sample
6 Polarization Dependence Return Loss​ Per sample
7 Directivity​ Per sample
8 Crosstalk​ Per sample
9 OTDR (per core)​ Per sample
10 Optical Gain​ Per sample
11 Gain Flatness​ Per sample
12 Noise Figure​ Per sample
13 Polarization Dependent Gain Per sample
14 Optical Signal-to-Noise Ratio​ Per sample
15 Chromatic Dispersion​ Per sample
16 Group Delay​ Per sample
17 Polarization-Mode Dispersion​ Per sample
18 PDL Per sample
19 Differential  Group Delay​ Per sample
20 WDL Per sample
21 Bit Error Rate​ Per sample
22 Extinction Ratio​ Per sample
23 Rise /Fall Time​ Per sample
24 Jitter Per sample
25 Signal to Noise Ratio Per sample
26 Optical Modulation Amplitude​ Per sample
27 Transfer Bit Rate​ Per sample
28 Cold Per hour​
29 Damp Heat​ Per hour​
30 Dry Heat​ Per hour​
31 Temperature-Humidity Cyclic Test Per hour​
32 Thermal Shock​ Per hour​

Services of Plasma Laboratory​ ​ ​

No. Service Type Description
1 Gas chromatography (GC)​ Per sample
2 Deposition and processing with RF (1)​ Per sample (<2min)​
3 Deposition and processing with RF (2)​ Per sample (2-5 min)​
4 Ellipsometry​ Per sample
5 Atomic Force Microscopy (AFM) Per sample
6 ATR Per sample
7 OES Per run​
8 Contact Angle​ Per hour​

Services of Laboratory of Organic and Polymeric Materials​

No. Service Type Description
1 Spectroscopy (transmission/ absorption)​ Dependent on the characteristics of film assuming that the material is prepared​
2 Spectroscopy (transmission/ absorption)​ Dependent on the characteristics of film assuming that the material is prepared​
3 Reflection spectroscopy​ Dependent on the characteristics of film assuming that the material is prepared​
4 Reflection spectroscopy​ Dependent on the characteristics of film assuming that the material is prepared​
5 Photoluminescence refection spectroscopy​ Dependent on the material and film type​
6 Spin coating (1)​ Dependent on the material and film type​
7 Spin coating (2)​ Dependent on sample
8 Deep coating (1) Dependent on sample
9 Deep coating (2) Dependent on sample
10 Evaporative coating Dependent on sample
11 Sample preparation for coating (1)​ Dependent on sample
12 Sample preparation for coating (2)​ Using z-scan configuration
13 Investigation of induced anisotropy (1) Using z-scan configuration
14 Investigation of induced anisotropy (2) Using z-scan configuration
15 Investigation of induced anisotropy (3) Dependent on the sample and desired number of images​
16 Resistance measurement of thin films (1)​ Dependent on the sample and desired number of images​
17 Resistance measurement of thin films (2)​ Dependent on the sample and time involved​
18 Refractive index and nonlinear absorption coefficient measurement (1)​ Dependent on the sample and time involved​
19 Refractive index and nonlinear absorption coefficient measurement (2)​ Dependent on the sample
20 Refractive index and nonlinear absorption coefficient measurement (3)​ Dependent on the sample
21 Sample analysis by transmitted light microscopy (1)​ Dependent on the sample
22 Sample analysis by transmitted light microscopy (2)​ Dependent on the sample and desired number of images
23 Ultrasonic bath​ Dependent on the sample and desired number of images
24 Ultrasonic bath​ Perform optical design and  specific configuration for measuring the desired parameter​​
25 Polymeric films (1) poling​ Dependent on the characteristics of film assuming that the material is prepared​
26 Polymeric films (2) poling​ Dependent on the characteristics of film assuming that the material is prepared​
27 Polymeric films (3) poling​ Dependent on the characteristics of film assuming that the material is prepared​
28 Magnetic stirrer (mixer)​ Dependent on the characteristics of film assuming that the material is prepared​
29 Magnetic stirrer (mixer)​ Dependent on the material and film type
30 Measurement of specific optical parameter of sample​ Dependent on the material and film type

Services of Laboratory of Solid-State Laser and its Applications

No. Service Type Description
1 Power measurement with laser energy​ Per measurement​
2 Profile registration of Laser ray​ Per sample
3 Use of nanosecond pulse YAG laser with power of 200 milijoule​ Per hour​
4 Use of nanosecond pulse YAG laser with power of 500 milijoule Per hour​
5 Use of femtosecond laser with nanojoule energy​ Per hour​
6 Ordinary fiber welding​ Per number​
7 Fiber welding PM​ Per number​
8 Use of class 10, 000 clean room with the area of 20 m2 Per day​
9 Use of fiber laser with power of 50 watt​ Per hour​
10 Other services related to use of laser sources​ -

Services of Laboratory of Laser Spectroscopy​

No. Service Type Description
1 Presentation of LIBS spectrum of solid samples Per sample
2 Presentation of LIBS spectrum of liquid and gas samples Per sample
3 Deep elemental analysis Per sample
4 Laser pulse radiation on sample Per pulse​
5 Presentation of absorption, transmission and reflection spectrum Per sample
6 Radiation measurement in the spectral region Per sample
7 Presentation of Raman/LIF spectrum​ Per sample